This all comes down to the rules.....1. references....does the contractor have them??? I ALWAYS furnish all my prospective customers them....no excuses...2. insurance....again, I always furnish proof....3. Read the proposal carefully...I ALWAYS list materials down to tape used, the brand, the grit of sandpaper, the manufacturer, etc....its INEXCUSABLE to not list all of these items....I am a member of the PDCA, the Painting and Decorating Contractors of America, the foremost authority in the coatings industry and they also approve of what I listed....if you do not follow these guidelines, you will NOT get a job reflective of "professional". Look for the PDCA where any painting contractors are, if they are not a member, RUN!
A fresh coat of paint makes everything it touches seem brand new. But such new beginnings cost real money. Professional painters charge around $4,000 for labor and materials to paint the exterior of a 2,500-square-foot, two-story home and roughly $5,500 for the interior. Painters’ rates may range from $20 to $60 an hour, but around $40 is typical in urban areas.
Hi Elaine, We would be happy to get you connected with a painting and wallpaper pro. You can submit a service request on our website: http://www.homeadvisor.com/ or browse reviews for local pros here: http://www.homeadvisor.com/c.html. We can also have a project advisor reach out to assist you if you send your contact information to [email protected] –HASupport
You can save a bundle by doing the labor yourself. The biggest DIY expense is paint. Other expenses include buying or renting supplies and equipment, like caulk, primer, brushes, rollers, tarps and ladders or scaffolding. Freeman advises applying paint with brushes, not a sprayer. “If you overspray all the window frames and overspray your shingles and your sidewalks and the brick on the front of the house, you do damage that is not easily fixed,” he says.
The pros were split on this tip. "Masking tape is problematic," says Mark Dixon, a painter in Missoula, Montana, and author of "House Painting Inside and Out" (Taunton Press, 1997). "Paint can bleed behind the tape, or remove the paint it's stuck to." Another problem is bridging. "Latex paints form a skin," says Dixon. "Removing painted tape can tear the skin, resulting in a ragged rather than a sharp line." Lastly, taping takes time. "Learning how to cut in with a brush takes practice, but if you can do it, you'll leave most tapers in the dust," Dixon says. (Cutting in is painting just the surface you want, not the surface adjacent to it — for example, where a wall meets the ceiling.) On the other hand, "If you can't cut in, you can't beat tape," says Span. The pros we spoke with all recommend painter's (blue) tape because it's easier to remove than masking tape. To prevent bleeding, Span uses a putty knife to bed the tape. After letting the paint dry, he scores the edge of the tape line with a utility knife to avoid tearing the paint.
The cost to paint the exterior of your home will vary depending on the size of your home, the condition of your siding, type of paint used and other factors. The average cost for labor and supplies ranges between $1,800-$3,800 and it may cost $6,500 or more for a large, custom project. In addition, you may need to pay more if there is damage to your siding or other challenging aspects of your job.

So why not just paint your own home. I'm not a painter, so my wife and I take our time, buying the paint and supplies, and doing our own painting. Yes, we need to tape, and it's not perfect, but we get the satisfaction of seeing our completed work. Get the supplies, sliders for your furniture, and patience and go for it. That way YOU have control over the entire project.
Want to know the color you pick will be good in your room? With this tool you can put it on some "walls" before you even paint. Here you can do it with Glidden's room visualizer tool linked below.  Either pick from our selections of rooms or upload your own and you can change walls and trim to find your perfect color. {^widget|(name)CtaButton|(Label)Paint+Your+Room+Online|(Url)https%3a%2f%2fwww.visualizecolor.com%2fglidden%23%2f|(ButtonID)Paint+Your+Room+Online|(Target)_blank|(Color)d6414d|(Edge)btn-rect|(GtmT)cta|(widget_displayname)CTA+Button^}
I agree with JHs. If there is no new color on it at all, just talk to the painter about it, if it was an honest mistake (which can happen very easily while painting) your painter should have no problem fixing it. However, in my years of experience, it is not unusual for 2 coats of door paint (good quality) not to cover very well at all. I once painted a red door 7 times, plus a tinted prime coat before I found the door to be a solid color.
Freshly painted walls often look blotchy. The color is uniform, but the sheen isn’t consistent. This usually occurs over the holes and cracks you patched with a filler or drywall compound. The porous fillers absorb the paint, dulling the surface (a problem called “flashing”). When light hits these dull spots, they stick out like a sore thumb. The smooth patch also stands out in contrast to the slightly bumpy texture of the rest of the wall. A quick coat of primer is all it takes to eliminate flashing and texture differences.
The materials of the home’s facade should be considered before painting your home. When painting flat surfaces like siding or wood, you can opt for standard outdoor paint. When painting a textured surface like stucco or brick, “elastomeric” paint is a much better choice. This type of paint can stretch more than normal paint, which allows it to bridge over small gaps and crevices, painting smoothly over texture.
Inspect the surface area for holes, cracks or other problems and apply acrylic caulk to fill them in. Use a putty knife to smooth out the caulk and remove any excess to prevent bumps. For particularly thin or narrow crevices, you may have to use your finger to smooth out the caulk. Caulk contracts and shrinks, so apply a second layer once it's dried.

Sanding not only feathers out chipped paint but also provides "tooth" for the next coat of paint. For glossy trim, use a sanding sponge rather than sandpaper. Sponges mold to the shape of the trim and last longer than paper. When applying latex over alkyd paint or when he is not sure of the original finish, Brian Doherty, a painter in Richmond, Virginia, follows the hand-sanding with liquid sandpaper to make sure the surface is completely deglossed to prevent incompatibility problems. "I've seen homes where latex was used on oil-painted trim, and the paint started to peel in less than a year," says Doherty.

When you choose Five Star Painting residential house painting contractors, you can feel confident that you are hiring the best in the business. Local Five Star painters have been serving clients throughout the United States and Canada since 2004. From taking time to prepare the area to using exactly the right equipment for each job, we make sure the project is done correctly. Our experience shows: We’re good at what we do, and our clients are always happy with the work we leave behind!
The only time it's acceptable to mix water in the paint is when you're using a deep or ultra deep base paint to reduce its stickiness, which is rare with new paint technology. Dark primary colors are composed almost entirely of tint that makes it very hard to work with without adding water. (You never use a sprayer and need to thin paint.?) If i was still in the industry I'd take the time to make a better article than this. Take this for a grain of slat. Use a reputable painter or someone you know you can trust or has been referred to you by someone you trust. I wouldn't hire anyone I had to watch like a hawk to make sure they're not screwing me.
The inland suburbs to the west, such as Orange Park and Fleming Island, are known for their reasonable housing prices. The more rural setting means that the homes in this area are very similar to homes in suburbs across the country rather than the large beach houses seen in Jacksonville’s seaside towns. Homes here have reasonable square footage, which can bring the cost of painting services down.
I hired this person because he was listed on Angie's List. This man claimed he took and passed his contractor's license test after he signed me up for a project (Feb.) that included fixing cracks, painting, repairing a gate, installing a screen door, etc. He said he would charge me the original "handyman" prices. He postponed the start date, brought one worker who fixed a few cracks, repainted the gate terribly, but ruined a dining room ceiling when his worker used silicone in a tube instead of the expansion tape, spray ceiling covering, and paint I had purchased saying this silicone was "better". Then they said they would have to paint the whole ceiling and charge extra. They left holes in the walls and did a sloppy paint job in several places. I just paid them to get them out of my home as I felt intimidated as a senior citizen who is handicapped. I will try to have the main guy come back when I let him know what I need redone. Don't know if he will come back without charging me more.
Because of our wet/cold weather, another painter was booked out through August as of May 7th, 2016.  Anyone even thinking about a VA loan refi should get estimates for painting and pest inspections BEFORE starting on the loan paperwork, otherwise you will have difficulty getting painting and inspections done in a timely manner (and it is my understanding this is common with VA loans.)  

Freshly painted walls often look blotchy. The color is uniform, but the sheen isn’t consistent. This usually occurs over the holes and cracks you patched with a filler or drywall compound. The porous fillers absorb the paint, dulling the surface (a problem called “flashing”). When light hits these dull spots, they stick out like a sore thumb. The smooth patch also stands out in contrast to the slightly bumpy texture of the rest of the wall. A quick coat of primer is all it takes to eliminate flashing and texture differences.


Even if you think you'll probably do the job yourself, it's good preparation to seek estimates from professional home painters, whether your painting the exterior or interior of your home. Then you'll have a financial point of comparison and you may benefit from what a home painting contractor has to say about the condition of your home, color choices and types of paint available. Let the painter make his pitch for a professional job before you decide what to do. You can still opt to do it yourself while having learned something worthwhile.
When painting the trim, you don’t have to be neat. Just concentrate on getting a smooth finish on the wood. Don’t worry if the trim paint gets onto the walls. You’ll cover it later when painting the walls. Once the trim is completely painted and dry (at least 24 hours), tape it off (using an “easy release” painter’s tape), then paint the ceiling, then the walls.
First off all clients want a "deal" As a painting contractor for 38 years I can tell you that residential-commercial-industrial clients (and their needs are all diffrent. It seems this discussion mostly concerns residential repaints,so here goes--first off ALWAYS get a personal referance from a friend or co-worker. Always get an itemized contract that specifies the prep,color, number of coats, and specifics on payment. Remember you want to set up a relationship with the painting contractor of your choice. Bond, license and insurance are required to get a contractors license and are readily available online at your state Labor and Industries website. Second-- find someone you trust. He or his crew will probably be left alone in your home for most of the time. I always tell my clients that I wont bring someone to their home I wouldnt have in mine. Third--$$ Dont ever pay up front always insist on progress draws if the project is 2 or 3 phases remember If a contractor wants $3000 to do the job and you give him half up front he will be working for $1500. It WILL affect the quality of the product. In 38 years of business I have never taken a deposit and have never not been paid in full remember do what you said you would do for exactly what you said it would cost and there will be no problems with getting paid. one last reminder to clients you are also being evaluated when you interview a contractor. He is sizing you up as well. If he thinks you are a bit sketchy the the price will go up or he wont take the job at all. I have turned down some jobs that looked very profitable on the surface that turned out not to be so.(word gets around fast in the small painting community) Good Luck to clients and contractors

To get basic measurements, measure the length and width of each wall you want to paint in inches. Multiply the length and height together, and divide by 144. This will give you the square footage for each wall. A gallon of paint typically covers around 400 square feet. In some cases, you may need a primer 2 first, then a single coat of paint, meaning that you may need one gallon of primer and one gallon of paint to cover 400 square feet. However, if the wall requires multiple coats, this will increase the total amount of square footage required, and therefore the amount of paint.
The only time it's acceptable to mix water in the paint is when you're using a deep or ultra deep base paint to reduce its stickiness, which is rare with new paint technology. Dark primary colors are composed almost entirely of tint that makes it very hard to work with without adding water. (You never use a sprayer and need to thin paint.?) If i was still in the industry I'd take the time to make a better article than this. Take this for a grain of slat. Use a reputable painter or someone you know you can trust or has been referred to you by someone you trust. I wouldn't hire anyone I had to watch like a hawk to make sure they're not screwing me.

Joseba and María are a very special partner. They have marked the character of the house. He is a renowned painter (www.sanchezzabaleta.com) who comes from Basque country to Gaucin attracted by the position and the views of the city. He needed a place to work and looked for an architect who understood his ideas of the lights and the space. The work developed shared the client and the architect ideas
Not only do I agree with what you are saying; but, I will not use Angie's List for referrals again. Their "A" rated painter did some of the exact things they are now warning against; however, they are still rated "A". I sent in a review and it took eight weeks to post it. They allowed the contractor to lie about what happened as a response. I had proof and photos. Angie's List is a scam; instead ask neighbors and friends for referrals!
Comment: Freshening up a well kept home for sale: paint stairwell and one bathroom, paint and possibly repair exterior front door surround, paint front door, remove, paint and replace palladian window on second floor (easy to access), paint baseboards and woodwork where needed, possibly paint (same color) small kitchen walls, paint inside and out of sun room windows, as needed.
This job is usually done by a professional house painter. The painter will assess the walls, clean, and make any necessary repairs or removal of old wall coverings. They will also tape off any adjacent surfaces and cover nearby furniture and floors with drop cloths. Typically, they will apply a layer of primer, then one to three coats of paint, depending on the color and coverage. Once the paint is dry, they take a final walkthrough to inspect and make any necessary touch ups. 

Painting the exterior of your home is an essential maintenance task that can be challenging, time-consuming and extremely messy. The fastest and safest way to get the job done right is to hire a professional exterior painting contractor. A pro will have the right tools, equipment, and experience for the job, will be able to recommend the most effective paints for your particular project, and can handle the necessary prep work to ensure a lasting finish. They will also select the best time to paint your home to keep the project within your timeline and budget.

"Bear Creek Painting did a great job on my house trim. I was having new gutters put on my house but realized that the trim needed to be scraped and painted. Nick was able to get his crew out within a few days. Their work was excellent, timely and Nick was professional and responsive to my need to get the work done quickly. I would definitely use Bear Creek painting for my next painting project."


"Cutting in is an acquired skill, but it's something you can't do at all with a ratty brush," says Doherty. When cutting in on a wall, he loads his brush and spreads out the excess paint, then works the brush up to the line between wall and ceiling. A brush stroke that's too wide creates a hatband, or smooth brushed band, on the very top of the wall where it meets the ceiling. To avoid this, Dixon recommends rolling first and then cutting in with a brush. "A good roller can get within 1/2 inch of the ceiling," he says. "You'll save time by not brushing more then you have to." When painting baseboards, "a wide taping knife makes a good paint guard," says Span. "Just keep the blade clean to prevent drips from working around the edge of the knife."
Painting is a skilled job with plenty of room for error, from knowing how to prepare the appropriate surface to understanding the best interior paint for the situation. When you book through Handy, we match your job’s requirements with experienced house painters who will leave you completely satisfied. They'll arrive with the right equipment in hand, ready to roll.
I learn a lot from this show and it help in my building maintenance job. i like this about the regulator on gas meter but for the cut away I know it had to be that way but Richard could you have mentioned that there was a vent on the regulator. I had a coworker ask me to check the vent and make sure it was clear, but from your cut away and no mention of a vent in the demo I didn't know there was a vent on the regulator so for next time there may need to be 2 cut aways explaining what the meter is and how to be safe.
Sand the trim with a fine-grit sanding sponge. Sponges get into crevices where sandpaper can’t go and let you apply even pressure. Then apply the first coat of paint, let it dry at least 24 hours, lightly sand it again for a completely smooth surface, and apply the second coat. After each sanding, vacuum the trim, then wipe it down with a tack cloth to remove the dust.
we only use the best interior paint which goes further as far as pricing a repaint we charge 2.00 a square foot floor space for walls ceilings and trim .on new construction using the best paint 3.90 per foot floor space that is with 3 coats on all surfaces but as being a professional for 45 years i recommend use a professional so that your paint will last longer and you wont have to pay to have it done more often i do free consulting in these areas i am more than happy to assist you with your projects 864-506-6666 just always remember good paint last longer and use a washable paint your home is your most valueable investment take care of it
Deciding which paint to use has gotten much easier now that acrylic latexes have pushed oil-based paints almost to extinction. The acrylics offer superior performance (they don't harden with age, the way oils do, so they move and breathe without blistering), they don't mildew as readily, and they emit fewer VOCs, so they comply with new air-quality regulations. They also work over both oil- and water-based primers.
Before the scrubdown, protect nearby plants by misting their leaves and saturating the surrounding soil with water, pulling them away from the house, and shrouding them in fabric drop cloths. (Plants will cook under plastic.) Lay more drop cloths along the base of the walls to collect any falling paint debris. Walls should be wet down before getting scrubbed, then washed with a gallon of water mixed with 1 cup chlorine bleach and 1 cup of either a concentrated, phosphate-free cleaner, such as a trisodium phosphate (TSP) substitute, or Jomax House Cleaner. Working in sections, from the bottom to the top, will avoid streaks. Be sure to rinse walls well before the solution dries. Wood siding and trim should be ready to paint after a day or two of dry weather.
Are you looking for interior house painters that are local, reliable and the best at what they do? Does the idea of painting the walls of your home fill you with dread? If you want to get the best results with minimal fuss, then make Handy your first choice when you need to connect with expert painting contractors. From preparing your interior walls and ceilings to achieving a neat, professional finish, Handy will put you in touch with the right people for the job. Customize your request by specifying your job details, from how many painters you need to how long you’ll need them. We’ll connect you with the painting professionals that suit you best with no compromise on quality.

Spills and spatters happen, regardless of how careful you are. It’s a lot easier to pre- pare for them than to wipe them out of your carpeting or off your wood floor later. All it takes is canvas drop cloths in your work area (a 4-ft. x 15-ft. cloth costs $15). The thick canvas stays in place, so you don’t need to tape it, and you can use it to cover any surface. Plastic drop cloths are slippery to walk on or set a ladder on and don’t stay in place. Even worse, paint spills on plastic stay wet, and they can end up on your shoes and get tracked through the house. Canvas is slippery on hard floors, so rosin paper ($10 for 400 sq. ft. at home centers) is better over vinyl, tile and hard- wood. Tape the sheets together and to the floor to provide a nonslip surface.

If you are unsure about what colors will work best in a space, you may wish to hire an interior decorator to help. Decorators can look at your furnishings, the size and shape of a room, and the amount of light it gets to help you determine the best shades for the space. Design services cost around $50 to $200 an hour, and can help you find the perfect colors for your home.


However, David, who works in Excel's office, really left a bad taste in our mouth for the whole project. We didn't love the color our house ended up being - a color match that Excel performed for us - and expressed as such. David was a nightmare to work with once we mentioned we had a problem. He had terribe customer service skills and repeatedly made us feel like it was our fault and that we were stupid. Painting our house was a big commitment and investment in our eyes, and he was not the least bit helpful in trying to get us to an end product we would be happy with. In fact, he succeeded in making us even more unhappy to the point that we gave up on even having Excel repaint to get us to a color we'd be happy with. A very disappointing experience.
Other than knowing what to look for when you consider different Atlanta house painters, knowing what to expect when it comes to cost, and how long a paint job should take, is probably the most helpful information. HomeAdvisor.com tracks both figures using customer surveys that we send out to homeowners after a job is completed. Based on that information, we've found that an average exterior paint job in Atlanta runs $2,500, and takes four days to complete. As you'd expect, those numbers vary depending on where you live and the size of your home. Just looking at the data we've collected, costs can range from $1,000 to $7,000, and jobs can take as little as a day, and as long as two weeks. It just goes to show that the only surefire way to know exactly what to expect is to seek out the services of a professional home painter in Atlanta.
We are completely dedicated to making sure our customers are satisfied with the painting services we provide. We use only our top notch tools and paint so you know you can depend on the work we do for you. We will complete any job you hire us for as efficiently as possible and within any budget you set. As a residential paint contractor, we can paint the interior or exterior of your home or office. We can also provide our pressure cleaning service on any surface on your property to get rid of dirt and make sure it's completely clean and ready for us to paint.
To get basic measurements, measure the length and width of each wall you want to paint in inches. Multiply the length and height together, and divide by 144. This will give you the square footage for each wall. A gallon of paint typically covers around 400 square feet. In some cases, you may need a primer 2 first, then a single coat of paint, meaning that you may need one gallon of primer and one gallon of paint to cover 400 square feet. However, if the wall requires multiple coats, this will increase the total amount of square footage required, and therefore the amount of paint.
×