Sand the trim with a fine-grit sanding sponge. Sponges get into crevices where sandpaper can’t go and let you apply even pressure. Then apply the first coat of paint, let it dry at least 24 hours, lightly sand it again for a completely smooth surface, and apply the second coat. After each sanding, vacuum the trim, then wipe it down with a tack cloth to remove the dust.
Riverside and San Marco are neighborhoods on the southern side of Jacksonville. These are some of the older neighborhoods, with many homes dating back to the early 1900s. Painting services in this area cost slightly more because of the older architecture and the larger sizes of the homes. There are newer homes in the Southside neighborhood, which has seen tremendous growth since the 1990s.
With that said, here's the reality of that particular scenario. Painters do put water in the paint, but not for reasons you would think. Some materials need to have their viscosity manipulated in order to slow drying time, allowing gravity to 'smooth' out the product for a better finish. It also prevents 'drags' and 'sausages'. I personally try not to do it too often, but from time to time I have to. I want my client to have a proper finish.
Freshly painted walls often look blotchy. The color is uniform, but the sheen isn’t consistent. This usually occurs over the holes and cracks you patched with a filler or drywall compound. The porous fillers absorb the paint, dulling the surface (a problem called “flashing”). When light hits these dull spots, they stick out like a sore thumb. The smooth patch also stands out in contrast to the slightly bumpy texture of the rest of the wall. A quick coat of primer is all it takes to eliminate flashing and texture differences.
If the point of hiring a well established, experienced, reputable painting contractor is to secure the professionalism and trust suggested to be inherent with that choice, then I would EXPECT that professionalism and experience to include the ability to make the proper and correct calculations for labor and materials for a fixed price quote, and there should be NO reason for the contractor to put the cost burden of their miscalculation on the consumer.

When it comes to painting your house interiors, you need professional results. Whether it’s a full remodel of the house or a new accent wall, your home deserves a high-quality service and an impeccable finish. Our CertaPro Painters® interior house painting services provide a seamless, efficient, and meticulous interior painting job that will make a world of difference to your home’s overall look and impact.


I would not recommend this company for the following reasons:1. Original appointment was very specific to them on what was needed and to take photos for 3 apartment unit plumbing fixture repairs. One unit had a bathroom tub/shower backup.2. No photos taken, 3 trips later and only 1 unit completed to satisfaction. (Backup) 3. Other faucets unable to find on line with their suppliers and repair 4. Had to find another plumbing company to complete the jobs. 5. Invoicing had to be redone as not in detail of job address for tax purposes 6. Bad communication throughout the project process with their internal customer service. Their technician and project manager ordering parts. 7. For the back up. Did not bring out correct snake on both trips and had to replace lines as too small to break through backup. Costing over $800 for 3 trips just to complete that situation out. 8. Ordered the wrong parts when 2nd trip out since no photos taken to confirm what was needed. Very dissatisfied and will never ask them to work in any of our rental properties again.
Painting professionals might charge more or less to paint your home's exterior based on its construction material. Some materials cost more to paint than others because of their texture, the paint required to properly cover them, and whether specialized materials are required to prepare them for painting or the elements. Find more information on the various types of siding available, as well as how much it might cost to paint or prepare each.
I'm an architect and my firm routinely specifies interior finishes for projects so I thought I'd contribute a professional's perspective on the issue of how many coats of paint are deemed "acceptable". The fact of the matter is the average consumer usually isn't a paint expert and can't be expected to know about all the factors that impact coverage. That knowledge is considered "means and methods" and in a court of law, the responsibility lies with the painter or general contractor, not the consumer. What the consumer should be concerned about is the final result-does it look good and is it what you expected? The simplest way to communicate this to your painter is to stipule in your written agreement that the number of coats will be "as required to cover". That way all the guess work about what kind of primer, how many coats, how color affects the scope of work, etc., is removed from the consumer's responsibility and resides where it belongs-with the professional. In the contract that's why retention is always a good idea-typically 10% is withheld from payment until the job is completed to the satisfaction of the customer. Of course in return you as the customer have to be reasonable about what constitutes a completed job. Just my $.02.
I put out a request for bids to several local house painters and quite a few seemed high. One was for over $6000 for painting the exterior of the house with putty fill as necessary, paint included. It was for him and one other guy to do the work. I said, "it's going to take you guys quite a while to get this job done" and he told me that no, they could do it in 2 days. I don't know about you but $1500 a day per painter seems more than just a bit high. I went with someone else and they had several people there for several days working like crazy and did a great job. There are too many scammers.
This painter Scot never came and finished the job.  Texted me at 6:30 in the morning saying that he isn't able to do the job I gave him.  I would not recommend this painter to anyone.  I will make sure everyone I know won't use this guy.  He is the worse business owner I have ever met. I don't know how he is in business.  Be very careful of this guy Scot.  Don't trust him and don't pay him for anything for any work.
When you refinish your existing cabinet doors, you get a whole new look without the astronomical costs normally associated with a kitchen remodel. It’s a much smarter way to update your space, especially if your cabinets are still in good condition. It doesn’t make sense to throw out perfectly good materials, just because you’re tired of the color.

If you are unsure about what colors will work best in a space, you may wish to hire an interior decorator to help. Decorators can look at your furnishings, the size and shape of a room, and the amount of light it gets to help you determine the best shades for the space. Design services cost around $50 to $200 an hour, and can help you find the perfect colors for your home.

The article and comments were great information to have before deciding how to go about getting a painting job done. I think the important point is that there are several key choices (who to do the work; color, sheen, quality, of paint; how many coats; amount of prep/repairs to be done and by whom, how long the job will take, provisions for changes, how detailed the contract needs to be; advanced deposit/progress payments/final payment; final inspection, etc.) that need to be made and it requires advanced research and planning in order to become well enough informed to make the right choices. Then it requires spending sufficient time to check materials and inspect the quality of the work while it is on-going, raher than waiting to do it all at the end. President Reagan's philosophy of "Trust, but verify." applies.
I'm an architect and my firm routinely specifies interior finishes for projects so I thought I'd contribute a professional's perspective on the issue of how many coats of paint are deemed "acceptable". The fact of the matter is the average consumer usually isn't a paint expert and can't be expected to know about all the factors that impact coverage. That knowledge is considered "means and methods" and in a court of law, the responsibility lies with the painter or general contractor, not the consumer. What the consumer should be concerned about is the final result-does it look good and is it what you expected? The simplest way to communicate this to your painter is to stipule in your written agreement that the number of coats will be "as required to cover". That way all the guess work about what kind of primer, how many coats, how color affects the scope of work, etc., is removed from the consumer's responsibility and resides where it belongs-with the professional. In the contract that's why retention is always a good idea-typically 10% is withheld from payment until the job is completed to the satisfaction of the customer. Of course in return you as the customer have to be reasonable about what constitutes a completed job. Just my $.02.
additionalType URL  An additional type for the item, typically used for adding more specific types from external vocabularies in microdata syntax. This is a relationship between something and a class that the thing is in. In RDFa syntax, it is better to use the native RDFa syntax - the 'typeof' attribute - for multiple types. Schema.org tools may have only weaker understanding of extra types, in particular those defined externally.
The best time to tackle windows is in the beginning of the day, when you're fresh," says Doherty. "But it still takes me an hour to do a standard window." For double-hungs, begin by raising the inner sash and lowering the outer sash until their positions are almost reversed. Paint the lower half of the outer sash first, then the entire inner sash. Once the lower sash is dry, return both to their normal position, but leave them slightly open. Finish painting the outer sash. "Windows take too long to tape," says Doherty. When painting, overlap the glass by 1/16 inch to seal the wood.
Deciding which paint to use has gotten much easier now that acrylic latexes have pushed oil-based paints almost to extinction. The acrylics offer superior performance (they don't harden with age, the way oils do, so they move and breathe without blistering), they don't mildew as readily, and they emit fewer VOCs, so they comply with new air-quality regulations. They also work over both oil- and water-based primers.
We had a bad experience with an interior painter years ago, with the crux of the problem being him overcharging us at the end for "extra work" he didn't anticipate. One thing I'd strongly recommend is making sure it's in the contract that any additional work or growth work is estimated and communicated to the owner as soon as it is identified, otherwise the owner is not liable to pay it at the end.

For your convenience MDE publishes this list of accredited lead contractors that meet Maryland’s standards to perform abatement activities involving lead-based paint. The list is an information resource only. MDE does not endorse any of the contractors included on this list nor does MDE provide any warranty about their performance. Consumers are advised to request bids and conduct reference checks before hiring. Contact the individual contractors for information regarding services and fees. Verify with the contractor you are going to hire that the supervisor is accredited by MDE and all lead paint abatement workers have current training. This accreditation and training does not satisfy the EPA Renovation, Repair and Painting (RRP) Rule.


To begin, move everything out of the room. Every painter we spoke with had a horror story about the time he didn't follow Rule No. 1. Bigger pieces of furniture can sometimes be left covered in the center of larger rooms, but if you are repairing drywall, says Chris Span, of Span's Quality Painting in Mobile, Alabama, "Take everything out. Drywall dust goes everywhere." Remove doors, light fixtures and hardware, and label everything with masking tape. Also, invest in drop cloths. "It's surprising how well a few drops of paint can cover a floor," says Rich Maceyunas, of Maceyunas Painting and Wallpaper in Waterbury, Connecticut. Buy high-quality drop cloths, such as canvas or paper-backed plastic. (Paint soaks right through lightweight fabrics and bedsheets.) Plastic sheeting works, but it's very slippery and doesn't absorb drips.
To get basic measurements, measure the length and width of each wall you want to paint in inches. Multiply the length and height together, and divide by 144. This will give you the square footage for each wall. A gallon of paint typically covers around 400 square feet. In some cases, you may need a primer 2 first, then a single coat of paint, meaning that you may need one gallon of primer and one gallon of paint to cover 400 square feet. However, if the wall requires multiple coats, this will increase the total amount of square footage required, and therefore the amount of paint.
Sorry it is difficult to trust almost anyone in the trades. It is easier to do the work myself and not deal with strangers in and around my house. When I have to hire someone I tell them up front that I'll be checking every detail, pay extra to purchase the materials myself, and if they don't want the job - well good! I always fine someone who will work with me as I pay a bonus for that.
A good paintbrush is key to a professional-looking finish. "A quality brush costs $15 to $25, but you'll discover that pros aren't as talented as you thought," says Doherty. "The equipment has a lot to do with their success." Most of our pros prefer natural-bristle brushes for oil-based paints, but they recommend synthetics for all-around use. When choosing a brush, pay attention to the bristles. Synthetic brushes are made of nylon or polyester, or a combination of the two. Poly bristles are stiffer, which makes them good for exterior or textured work, but for fine interior work, Doherty uses softer nylon brushes. Look also for tapered bristles, which can help you work to an edge, and flagged tips, which help spread the finish smoothly and evenly. Brushes are available in 1- to 4-inch widths. Most painters keep an arsenal on hand to match the job. "Use common sense," says Maceyunas. "A smaller brush gives you more control, but no one wants to paint a door with a 1-inch-wide brush." Doherty recommends starting with a 2- or 2-1/2-inch sash brush. The angled brush makes it easier to cut to a line and puts more bristles on the work than a square-tipped brush.
In some cases, professional painters may include additional charges for specialized equipment that homeowners can't purchase on their own. Because professionals have licenses and access to such equipment, it's simpler to let them get those themselves. But providing some of the smaller equipment and extras directly really can help to cut down on the total cost of your project.
Home Works Painting is licensed (Virginia Class A #2705-153298) and insured (Workman’s Comp and General Liability), and has been servicing Northern Virginia since 2005. We pride ourselves on delivering a first class job with exceptional service. Home Works Painting has been selected as Northern Virginia’s Best Pick for painters for the past seven years, and is a member of Painting and Decorating Contractors of America (PDCA).
If there is any peeling — and there usually is somewhere — it's essential to scrape off any loose paint. This doesn't just mean the parts that are already separated from the wood and ready to fall off on their own. Each spot where paint has peeled loose needs to be scraped thoroughly until you can no longer get the sharp corner of a putty knife under any of the surrounding edges of paint. Then, the bare spot needs to be sanded until the paint edges are smooth.
Only a dummy gets involved with so-called "contractors." Hire a qualified actual worker yourself. Check out their resume/background, etc. RULE #1..NO ADVANCE DEPOSITS! Pay daily or weekly or upon satisfied completion according your standard, not workers. Contractors are merely employment agents. If that's the way you get work done, then go ahead and waste your money and wind up with the myriad of problems enumerated upon in the news clip above. RULE#2.. NO SMOKERS. They are lighting up on your money. RULE#3: No cell phones while working. Talk on their own time after work
Painters will need several supplies for your home exterior project in addition to paint. Consider personally providing any materials that can be obtained without a license to reduce project costs. Painting supplies are also handy to have around for maintenance and touch-up jobs after the job is complete. The cost to invest in painting supplies will probably run you no more than $200 to $300, unless you buy really high-quality products from specialized paint shops. Consider purchasing the following:

Thorough preparation is essential to ensure a good finish. Contractors might have to fill cracks or holes and remove old paint if it is badly worn, peeling or flaking. They remove all paint and apply a suitable primer to the bare surface. If the existing paint is in reasonable condition, they clean it and rub it with abrasive material to provide a key for the new paint. On new surfaces, such as bare wood or fresh plaster, they apply a suitable seal, followed by a primer coat.
Located at the northern part of the state, Jacksonville is right along the Atlantic Ocean. In addition to year-round residents, many homeowners have homes in the area that they rent out to vacationers and tourists. This is especially true in suburbs, such as Neptune Beach, Sawgrass, and Atlantic Beach, that are located right along the water. Keeping rental properties in good condition and ensuring they have fresh paint guarantees that they are attractive to potential visitors. Using bright, beachy colors and quality paints that can stand up to the salty air can increase the overall cost of painting services in the area.

• One room or the whole house? Applying one coat in one room is a reasonable DIY Saturday project (especially if you have help and beer). Multiply the time spent moving furniture, prepping walls and sanding old trim by the number of rooms in the house, and you might want to hire real help. It's the same outside. You can probably tackle one shady garage wall that needs a little scraping and sanding plus a coat of paint, but covering all surfaces of the house is usually best left to a pro.


A mudroom may feel like a luxury, but in many regions, it's a necessity. If your small home is lucky enough to have a mudroom, you'll want to choose a color that is fun and cheerful without changing the dynamic of your entire color scheme. A natural green like Joanna Gaines' Magnolia Green is vibrant but still very natural. If your small home doesn't have a full mudroom, you can create one by adding an accent wall of color, coat hooks, and benches with storage. 
In 1894, a national association formed, recreating itself in 1918 as the National Federation of Master Painters and Decorators of England and Wales, then changing its name once again to the British Decorators Association before merging, in 2002, with the Painting & Decorating Federation to form the Painting & Decorating Association. The Construction Industry Joint Council, a body formed of both unions and business organizations, today has responsibility for the setting of pay levels.[2]
This is an update to my review from 2015 when they painted my 100+ year old craftsman.  Outstanding work, professional and meticulous with preparation and cleanup.  About a year and a half after the work was completed, I noticed some peeling and lifting on a shaded back corner of the house.  After some initial crossed emails, Excel re-prepped this area and repainted about 2.5 years after the initial job.  Same clean, professional work.  My neighbor also used them recently and their house looks great.  I will definitely plan on using them if I need painting services in the future.
Another factor to consider is the height and features of your home. An example would be a house completely trimmed in Cement Fiber, which does chalk if you do not purchase the correct paint and apply enough of it. Some houses in Coastal Areas are already on 15+ft Stilts (off ground) and then another 20ft high at times. This requires rental equipment and careful cost estimation based on the difficulty of the overall project, The best advice that I can give is to get several estimates in your area and make a decision a couple of weeks afterwards. You will "weed out" per se the individuals that do not have the patience to finish a project that was started-as well as those who haggle you for payment (sometimes daily) before project is completed. I have heard some wild stories from a lot of Homeowners. Common sense and your intuition will make you aware of anyone that you should not hire.

PSA: Color psychology is a thing. The right soothing hue can work wonders for your mind and soul. You might think that only works for pale blues, but the contrast of a light and dark color — or, in this case, off-white walls with chocolate brown and deep blue accents — has a powerful effect. "The darker color grounds the room, and then the lighter runs right up to the ceiling and makes it feel higher. It creates this serene atmosphere," designer Laura Bohn told us.

I'm an architect and my firm routinely specifies interior finishes for projects so I thought I'd contribute a professional's perspective on the issue of how many coats of paint are deemed "acceptable". The fact of the matter is the average consumer usually isn't a paint expert and can't be expected to know about all the factors that impact coverage. That knowledge is considered "means and methods" and in a court of law, the responsibility lies with the painter or general contractor, not the consumer. What the consumer should be concerned about is the final result-does it look good and is it what you expected? The simplest way to communicate this to your painter is to stipule in your written agreement that the number of coats will be "as required to cover". That way all the guess work about what kind of primer, how many coats, how color affects the scope of work, etc., is removed from the consumer's responsibility and resides where it belongs-with the professional. In the contract that's why retention is always a good idea-typically 10% is withheld from payment until the job is completed to the satisfaction of the customer. Of course in return you as the customer have to be reasonable about what constitutes a completed job. Just my $.02.
According to the EPA, professional painters must check for lead -- especially if a home was built before 1978. Many DIY painters forget to test for lead paint. Testing kits are available in home improvement stores for less than $40. You can also hire a lead testing and removal professional to do this work quickly and efficiently on your behalf. Lead paint can be dangerous; it's far better to find it before you put time and effort into painting your home than after the fact.
If you talk with a painting contractor long enough, you’ll inevitably hear; “There’s no good help out there.” It’s easy to hide behind this excuse, but it’s not true. There are plenty of reliable painters out there, business owners just don’t take the time to find them. It takes TIME to find good people, time you wouldn’t have if you were busy painting.

Specialty painting by the hour costs between $40 to $50 on average. Paint might range between $75 to $90, costing an additional $40 to $50 per hour. The painter's skill and experience are also determining factors in the cost of specialty painting. While a freelance artist might charge $25 to $30 an hour, a very skilled professional might charge $80 or more. Some painters might also charge $60 or more for a consultation. Trompe l'oeils, in particular, will run on the expensive end of the price spectrum. Return to Top
×