Here is where this affects you as a consumer. You select a painter with a contract that says 2 coats, $500 down. You give the company the deposit and pick your colors a couple of days before the project starts. The painter goes to the store with your colors and figures out they are deep base. He (or she) not only needs to charge you more for the paint, but he also needs to charge you for a dark gray primer coat. Ninety nine percent of the time that primer coat is going to be really, really expensive since you already gave a deposit.
Hi Elaine, We would be happy to get you connected with a painting and wallpaper pro. You can submit a service request on our website: http://www.homeadvisor.com/ or browse reviews for local pros here: http://www.homeadvisor.com/c.html. We can also have a project advisor reach out to assist you if you send your contact information to [email protected] –HASupport
The best time to tackle windows is in the beginning of the day, when you're fresh," says Doherty. "But it still takes me an hour to do a standard window." For double-hungs, begin by raising the inner sash and lowering the outer sash until their positions are almost reversed. Paint the lower half of the outer sash first, then the entire inner sash. Once the lower sash is dry, return both to their normal position, but leave them slightly open. Finish painting the outer sash. "Windows take too long to tape," says Doherty. When painting, overlap the glass by 1/16 inch to seal the wood.
Inspect the surface area for holes, cracks or other problems and apply acrylic caulk to fill them in. Use a putty knife to smooth out the caulk and remove any excess to prevent bumps. For particularly thin or narrow crevices, you may have to use your finger to smooth out the caulk. Caulk contracts and shrinks, so apply a second layer once it's dried.
Small random-orbit or pad sanders make this job go faster. (Wallis first covers these boundaries with Synkoloid patching compound so no edge is visible after sanding.) As shown, you want to make sure that there is a feathered, smooth transition from exposed wood to old paint. For areas that might get close scrutiny, you can follow up with a 100- or 120-grit rubdown to erase any scratches.

When painting the trim, you don’t have to be neat. Just concentrate on getting a smooth finish on the wood. Don’t worry if the trim paint gets onto the walls. You’ll cover it later when painting the walls. Once the trim is completely painted and dry (at least 24 hours), tape it off (using an “easy release” painter’s tape), then paint the ceiling, then the walls.
Estimates are one of the most important tools to help you land the next job. During our most recent webinar series on estimating, Fred Yarur of PEP (Painter’s Estimating Program) outlined 10 foundational principles to support effective estimating procedures. Use estimate tools. These enhance your ability to make informed decisions. Estimating is the process of […]
However, David, who works in Excel's office, really left a bad taste in our mouth for the whole project. We didn't love the color our house ended up being - a color match that Excel performed for us - and expressed as such. David was a nightmare to work with once we mentioned we had a problem. He had terribe customer service skills and repeatedly made us feel like it was our fault and that we were stupid. Painting our house was a big commitment and investment in our eyes, and he was not the least bit helpful in trying to get us to an end product we would be happy with. In fact, he succeeded in making us even more unhappy to the point that we gave up on even having Excel repaint to get us to a color we'd be happy with. A very disappointing experience.
Most pros don't bother cleaning brushes and rollers if they are going to use them the next day on the same job. "Latex paint dries slowly in cold temperatures," says Maceyunas. For two-day jobs, he wraps the rollers and brushes in plastic grocery bags and sticks them in the refrigerator. "Just allow the roller to return to room temperature before reusing it," he says. Roller covers are almost impossible to clean thoroughly. Most pros buy new covers for each job.

"Cutting in is an acquired skill, but it's something you can't do at all with a ratty brush," says Doherty. When cutting in on a wall, he loads his brush and spreads out the excess paint, then works the brush up to the line between wall and ceiling. A brush stroke that's too wide creates a hatband, or smooth brushed band, on the very top of the wall where it meets the ceiling. To avoid this, Dixon recommends rolling first and then cutting in with a brush. "A good roller can get within 1/2 inch of the ceiling," he says. "You'll save time by not brushing more then you have to." When painting baseboards, "a wide taping knife makes a good paint guard," says Span. "Just keep the blade clean to prevent drips from working around the edge of the knife."


The inland suburbs to the west, such as Orange Park and Fleming Island, are known for their reasonable housing prices. The more rural setting means that the homes in this area are very similar to homes in suburbs across the country rather than the large beach houses seen in Jacksonville’s seaside towns. Homes here have reasonable square footage, which can bring the cost of painting services down.
One of the fastest, most effective ways to personalize your living space is with color. Bright, muted, cheerful, elegant—whatever your mood, personality, or preference might be, there’s a paint color to match! Our local Five Star Painting teams specialize in making houses feel like homes through interior and exterior home painting services. If you're looking to transform your home, it's time to contact Five Star Painting. Call (888) 261-3633 for a free estimate, or schedule an appointment online. Let us help you paint your world!

To maintain a wet edge, start near a corner and run the roller up and down the full height of the wall, moving over slightly with each stroke. Move backward where necessary to even out thick spots or runs. Don’t let the roller become nearly dry; reload it often so that it’s always at least half loaded. Keep the open side of the roller frame facing the area that’s already painted. That puts less pressure on the open side of the roller, so you’re less likely to leave paint ridges when doing DIY wall painting.
So sad that Angie's List requires the contractor be notified!! They have lost me as a client. If I'm dissatisfied and want to give an "F" rating (question/workers...I SHOULD NOT be intimidated into passing up an opportunity to explain my experience! There is NO WAY my contractor got an Aplus rating from over five hundred people....so someone was lying....yet I can't report that without the contractor knowing it? REALLY?

I'm hiring an interior painter and that is why I was reading this comment list. I'm concerned about your comment about Angie's List. Some of us don't have personal recommendations for tradespersons, and rely on sites like this. Are you saying that Angie's List's reviews are not complete or that they do not print some of the negative reviews? It's hard to know what to do - I have not been able to find a person who just had their paint done so I can ask him/her about the quality of the painter.

the price can always be adjusted based on on or off season, amount of colors to be used. A job like this can be done in 2 days and much quicker with a helper. I charge a bit more than others just because its quality work done professionally. Theres others that charge more than this just because they can on the on season and most people dont get a 2nd bid...


Wilson & Hampton provides the premier system for coating metal surfaces. Electrostatic painting is an efficient process where you can upgrade and rejuvenate your entire office or factory area in your choice of finishes at a fraction of the re-placement cost. Cabinets, lockers, machinery, Bathroom Partitions and much more can be painted in-shop or on-site by drawing the paint directly to the metal surface to be painted and “wrapping” around it, leaving no drips, spatter, or over spray.
Even an old lamp with a bare bulb held close to a wall will make minor cracks, bumps or nail pops jump out. Carmen Toto, owner of C. Toto & Sons in Madison, New Jersey, uses painter's putty or a lightweight spackle for minor cracks and dents; he uses plaster of Paris for dents deeper than 1/8 inch. Instead of the standard tape-and-spackle method for bridging over recurring stress cracks, Maceyunas uses a rubberized spray-on primer called Good-Bye Crack. Damaged wood requires a slightly different approach. "Don't use spackle on wood," says Toto, "because it just won't stick." For damaged trim, he uses painter's putty or a two-part wood filler, such as Minwax's High Performance Filler. Smooth any repairs, bumps, and nibs with a drywall pole sander. For smoother walls and better adhesion, some of our pros sand all previously painted walls regardless of the shape they're in.

Customer Service/Scheduling: I ended up being admitted to the hospital about a week or so after we decided to go with Excel, with pregnancy related complications. When they reached out to me as a reminder for the deposit, I explained my situation, and asked for a little more time to see if we could even proceed. Without hesitation, they said this was not an issue. This company cares about the people they are working with, not filling up every single day with a job. We also went back and forth. At first we cancelled, and then we asked for the dates back, and they were so accommodating.
to be the devils advocate i have been a building contractor 20 of the last 30 yrs. i do know that if you go to a higher sheen of paint and or darker colors then any imperfections in the walls will show up much more dramatically…therefore the painter or a good drywall finisher is needed to prepare the walls extensively. this could cause more expenses…for it takes a lot of time to prep walls (smooth walls..not textured walls) and this cost has to be absorbed.

A fresh coat of paint makes everything it touches seem brand new. But such new beginnings cost real money. Professional painters charge around $4,000 for labor and materials to paint the exterior of a 2,500-square-foot, two-story home and roughly $5,500 for the interior. Painters’ rates may range from $20 to $60 an hour, but around $40 is typical in urban areas.
You want to convert a wall to dry erase board, coat it in clear or change the color of the wall. If you want it to match your filing cabinets and cubicles we can coat your wall with metallic colors.No longer do you have to have a WHITE dry erase board. You can now have it clear or colors for any surface. You can coat any chalkboard with clear and turn it into a dry erase board. It is now your choice for your décor. See our dry erase painting video here.
"Cutting in is an acquired skill, but it's something you can't do at all with a ratty brush," says Doherty. When cutting in on a wall, he loads his brush and spreads out the excess paint, then works the brush up to the line between wall and ceiling. A brush stroke that's too wide creates a hatband, or smooth brushed band, on the very top of the wall where it meets the ceiling. To avoid this, Dixon recommends rolling first and then cutting in with a brush. "A good roller can get within 1/2 inch of the ceiling," he says. "You'll save time by not brushing more then you have to." When painting baseboards, "a wide taping knife makes a good paint guard," says Span. "Just keep the blade clean to prevent drips from working around the edge of the knife."
A number of details will affect the cost of painting the exterior of your house, such as its size, accessibility and siding type. In many cases though, preparation often has the biggest impact on the bottom line.Your local exterior painting contractor will take a look at the project to determine how extensive repairs and preparation will be and if special equipment, materials or paints are needed to get the job done right.

Dave, you said it best! Every pro painting contractor truly worth their salt would and should cut and paste exactly what you say here about where customary and legitimate practices and expectations should be in regards to what customers should expect from contractors and how contractors should professionally deal with their customers. By the way, Dave, if you work in the Atlanta area, I would like to hire you! Thank you for your valuable advice!
Concrete walls must always be prepared before painting, but in some cases previous finishes will also have to be removed so that paint doesn't peel or chip off. Additionally, special sealants, primers and paints may be applied to ensure concrete's endurance in face of the specific elements. Depending on the wall's condition and exposure to the sun, painting professionals will usually estimate between $500 (~250 sq. ft.) and $2,000 (~1,000 sq. ft.), depending on wall area to cover.

Consider purchasing supplies personally to save money. Ask the painter for a bid that separates labor and materials. Then explain that you'll purchase the materials and ask for a list of exactly what will be needed to complete the job. Caulking, for example, is an extra supply commonly used to fill any cracks or damaged areas in your walls -- and one that might be overlooked in an incomplete list. 

Whether you are painting the exterior of your home to boost its curb appeal, change a color you don't like or refresh a dilapidated paint job, one thing is certain: Painting your home's exterior is a large job that requires proper planning, preparation and tools. In most cases, painting your home's exterior is a job best left to a pro. But before you call one in, you'll want to consider a few factors that will affect your project's cost.
Sanding not only feathers out chipped paint but also provides "tooth" for the next coat of paint. For glossy trim, use a sanding sponge rather than sandpaper. Sponges mold to the shape of the trim and last longer than paper. When applying latex over alkyd paint or when he is not sure of the original finish, Brian Doherty, a painter in Richmond, Virginia, follows the hand-sanding with liquid sandpaper to make sure the surface is completely deglossed to prevent incompatibility problems. "I've seen homes where latex was used on oil-painted trim, and the paint started to peel in less than a year," says Doherty.

Hi Donnie, Thanks for your comment! We would be happy to help you connect with a fencing pro to give you an estimate on your project. You can submit a request to our pros here: www.homeadvisor.com, browse a list of local pros here: http://www.homeadvisor.com/c.html, or send your info to [email protected] and a project advisor will reach out to assist you. –HASupport
When you choose Five Star Painting residential house painting contractors, you can feel confident that you are hiring the best in the business. Local Five Star painters have been serving clients throughout the United States and Canada since 2004. From taking time to prepare the area to using exactly the right equipment for each job, we make sure the project is done correctly. Our experience shows: We’re good at what we do, and our clients are always happy with the work we leave behind!
The best time of the year to paint your home is typically in late spring and early summer when it’s warm outside and moisture is low. This can change based on your geographic location. For example, fall can be a good time to paint in California when the difference between high and low temperatures is low. Your painter will select the optimal time to start your exterior painting project.
Hi Elaine, We would be happy to get you connected with a painting and wallpaper pro. You can submit a service request on our website: http://www.homeadvisor.com/ or browse reviews for local pros here: http://www.homeadvisor.com/c.html. We can also have a project advisor reach out to assist you if you send your contact information to [email protected] –HASupport
When you choose Five Star Painting residential house painting contractors, you can feel confident that you are hiring the best in the business. Local Five Star painters have been serving clients throughout the United States and Canada since 2004. From taking time to prepare the area to using exactly the right equipment for each job, we make sure the project is done correctly. Our experience shows: We’re good at what we do, and our clients are always happy with the work we leave behind!
When selecting a color scheme for the home’s exterior homeowners can choose color options that will correct flaws that they may feel exist with their home and property.  Some examples include utilizing two shades of a single color to make a home appear appropriately sized when the home may be too large or too tall.  To accomplish this effect individuals will want to place the darker tone on the upper level of the home’s exterior.  Smaller windows can appear more proportionately sized by trimming them in a lighter tone of paint.  Darker colors make a space or feature appear smaller.  The same effect can be obtained for homes positioned further away from a curb.  By using lighter tones the home will not feel camouflaged.
Professional painters provide estimates primarily based on the square footage of your home. Painting an average home between 500 and 1,500 square feet can cost between $1,000 and $3,000. However, factors such as number of stories and ease of access can also affect the overall price. Homeowners report that the average cost to paint a house nationally is $2,581 and most pay between $1,714 and $3,682.

Before the scrubdown, protect nearby plants by misting their leaves and saturating the surrounding soil with water, pulling them away from the house, and shrouding them in fabric drop cloths. (Plants will cook under plastic.) Lay more drop cloths along the base of the walls to collect any falling paint debris. Walls should be wet down before getting scrubbed, then washed with a gallon of water mixed with 1 cup chlorine bleach and 1 cup of either a concentrated, phosphate-free cleaner, such as a trisodium phosphate (TSP) substitute, or Jomax House Cleaner. Working in sections, from the bottom to the top, will avoid streaks. Be sure to rinse walls well before the solution dries. Wood siding and trim should be ready to paint after a day or two of dry weather.


A painter's rod, or pole, can help you paint ceilings more quickly — no climbing up and down ladders required. And there's no need to stand directly underneath the area you are painting, so you won't catch every wayward splatter. A pole is also great for walls and floors. The pros were split over whether the 4- or 8-foot pole is best for everyday use, but they all agreed that a telescoping rod is the best bet.
×